Convolution (computer science)

The heat transfer coefficient or film coefficient, in thermodynamics and in mechanical and chemical engineering, is the proportionality coefficient between the heat flux and the thermodynamic driving force for the flow of heat (i.e., the temperature difference, ΔT):

$h={\frac {q}{\Delta T}}$

where

q : heat flux, W/m² i.e., thermal power per unit area, q = dQ/dA

h : heat transfer coefficient, W/(m²•K)

ΔT : difference in temperature between the solid surface and surrounding fluid area, K

It is used in calculating the heat transfer, typically by convection or phase transition between a fluid and a solid.

The heat transfer coefficient has SI units in watts per squared meter kelvin: W/(m²K).

Heat transfer coefficient is the inverse of thermal insulance. This is used for building materials (R-value) and for clothing insulation.

There are numerous methods for calculating the heat transfer coefficient in different heat transfer modes, different fluids, flow regimes, and under different thermohydraulic conditions. Often it can be estimated by dividing the thermal conductivity of the convection fluid by a length scale. The heat transfer coefficient is often calculated from the Nusselt number (a dimensionless number). There are also online calculators available specifically for heat transfer fluid applications.

Composition

A simple method for determining an overall heat transfer coefficient that is useful to find the heat transfer between simple elements such as walls in buildings or across heat exchangers is shown below. Note that this method only accounts for conduction within materials, it does not take into account heat transfer through methods such as radiation. The method is as follows:

$1/(U\cdot A)=1/(h_{1}\cdot A_{1})+dx_{w}/(k\cdot A)+1/(h_{2}\cdot A_{2})$

Where:

• $U$ = the overall heat transfer coefficient (W/(m²•K))
• $A$ = the contact area for each fluid side (m²) (with $A_{1}$ and $A_{2}$ expressing either surface)
• $k$ = the thermal conductivity of the material (W/(m·K))
• $h$ = the individual convection heat transfer coefficient for each fluid (W/(m²•K))
• $dx_{w}$ = the wall thickness (m)

As the areas for each surface approach being equal the equation can be written as the transfer coefficient per unit area as shown below:

$1/U=1/h_{1}+dx_{w}/k+1/h_{2}$

or

$U=1/(1/h_{1}+dx_{w}/k+1/h_{2})$

NOTE: Often the value for $dx_{w}$ is referred to as the difference of two radii where the inner and outer radii are used to define the thickness of a pipe carrying a fluid, however, this figure may also be considered as a wall thickness in a flat plate transfer mechanism or other common flat surfaces such as a wall in a building when the area difference between each edge of the transmission surface approaches zero.

In the walls of buildings the above formula can be used to derive the formula commonly used to calculate the heat through building components. Architects and engineers call the resulting values either the U-Value or the R-Value of a construction assembly like a wall. Each type of value (R or U) are related as the inverse of each other such that R-Value = 1/U-Value and both are more fully understood through the concept of an overall heat transfer coefficient described in lower section of this document.

Convective heat transfer Correlations

Although convective heat transfer can be derived analytically through dimensional analysis, exact analysis of the boundary layer, approximate integral analysis of the boundary layer and analogies between energy and momentum transfer, these analytic approaches may not offer practical solutions to all problems when there are no mathematical models applicable. As such, many correlations were developed by various authors to estimate the convective heat transfer coefficient in various cases including natural convection, forced convection for internal flow and forced convection for external flow. These empirical correlations are presented for their particular geometry and flow conditions. As the fluid properties are temperature dependent, they are evaluated at the film temperature $T_{f}$, which is the average of the surface $T_{s}$ and the surrounding bulk temperature, ${{T}_{\infty }}$.

${{T}_{f}}={\frac {{{T}_{s}}+{{T}_{\infty }}}{2}}$

External flow, Vertical plane

Churchill and Chu correlation for natural convection adjacent to vertical planes. Nu_L applies to all fluids for both laminar and turbulent flows. L is the characteristic length with respect to the direction of gravity, and Ra_L is the Rayleigh Number with respect to this length.

${\mathrm {h} }\ ={\frac {k}{L}}\left({0.825+{\frac {0.387\mathrm {Ra} _{L}^{1/6}}{\left(1+(0.492/\mathrm {Pr} )^{9/16}\right)^{8/27}}}}\right)^{2}$

For laminar flows in the range of $Ra_{L}<10^{9}$, the following equation can be further improved.

${\mathrm {h} }\ ={\frac {k}{L}}\left(0.68+{\frac {0.67\mathrm {Ra} _{L}^{1/4}}{\left(1+(0.492/\mathrm {Pr} )^{9/16}\right)^{4/9}}}\right)\,\quad \mathrm {Ra} _{L}\leq 10^{9}$

External flow, Vertical cylinders

For cylinders with their axes vertical, the expressions for plane surfaces can be used provided the curvature effect is not too significant. This represents the limit where boundary layer thickness is small relative to cylinder diameter D. The correlations for vertical plane walls can be used when

${\frac {D}{L}}\geq {\frac {35}{Gr_{L}^{\frac {1}{4}}}}$

where $Gr_{L}$ is the Grashof number.

External flow, Horizontal plates

W.H. McAdams suggested the following correlations. The induced buoyancy will be different depending upon whether the hot surface is facing up or down. For a hot surface facing up or a cold surface facing down,

${\mathrm {h} }\ ={\frac {k0.54\mathrm {Ra} _{L}^{1/4}}{L}}\,\quad 10^{5}\leq \mathrm {Ra} _{L}\leq 2\times 10^{7}$

${\mathrm {h} }\ ={\frac {k0.14\mathrm {Ra} _{L}^{1/3}}{L}}\,\quad 2\times 10^{7}\leq \mathrm {Ra} _{L}\leq 3\times 10^{10}$

For a hot surface facing down or a cold surface facing up,

${\mathrm {h} }\ ={\frac {k0.27\mathrm {Ra} _{L}^{1/4}}{L}}\,\quad 3\times 10^{5}\leq \mathrm {Ra} _{L}\leq 10^{10}$

The length is the ratio of the plate surface area to perimeter. If the plane surface is inclined at an angle θ, the equations for vertical plane by Churchill and Chu may be used for θ up to $60^{o}$. When boundary layer flow is laminar, the gravitational constant g is replaced with g cosθ for calculating the Ra in the equation for laminar flow

External flow, Horizontal cylinder

For cylinders of sufficient length and negligible end effects, Churchill and Chu has the following correlation for $10^{-5}<\mathrm {Ra} _{D}<10^{12}$

${\mathrm {h} }\ ={\frac {k}{D}}\left({0.6+{\frac {0.387\mathrm {Ra} _{D}^{1/6}}{\left(1+(0.559/\mathrm {Pr} )^{9/16}\,\right)^{8/27}\,}}}\right)^{2}$

External flow, Spheres

For spheres, T. Yuge has the following correlation. for Pr≃1 and $1\leq \mathrm {Ra} _{D}\leq 10^{5}$

${\mathrm {Nu} }_{D}\ =2+0.43\mathrm {Ra} _{D}^{1/4}$

Forced convection

Internal flow, Laminar flow

Sieder and Tate has the following correlation for laminar flow in tubes where D is the internal diameter, μ_b is the fluid viscosity at the bulk mean temperature, μ_w is the viscosity at the tube wall surface temperature.

${\mathit {Nu}}_{D}={1.86}\cdot {{\left({\mathit {Re}}\cdot {\mathit {Pr}}\right)}^{{}^{1}\!\!\diagup \!\!{}_{3}\;}}{{\left({\frac {D}{L}}\right)}^{{}^{1}\!\!\diagup \!\!{}_{3}\;}}{{\left({\frac {{\mu }_{b}}{{\mu }_{w}}}\right)}^{0.14}}$

Internal flow, Turbulent flow

DTZ's public sale group in Singapore auctions all forms of residential, workplace and retail properties, outlets, homes, lodges, boarding homes, industrial buildings and development websites. Auctions are at present held as soon as a month.

We will not only get you a property at a rock-backside price but also in an space that you've got longed for. You simply must chill out back after giving us the accountability. We will assure you 100% satisfaction. Since we now have been working in the Singapore actual property market for a very long time, we know the place you may get the best property at the right price. You will also be extremely benefited by choosing us, as we may even let you know about the precise time to invest in the Singapore actual property market.

The Hexacube is offering new ec launch singapore business property for sale Singapore investors want to contemplate. Residents of the realm will likely appreciate that they'll customize the business area that they wish to purchase as properly. This venture represents one of the crucial expansive buildings offered in Singapore up to now. Many investors will possible want to try how they will customise the property that they do determine to buy by means of here. This location has offered folks the prospect that they should understand extra about how this course of can work as well.

Singapore has been beckoning to traders ever since the value of properties in Singapore started sky rocketing just a few years again. Many businesses have their places of work in Singapore and prefer to own their own workplace area within the country once they decide to have a everlasting office. Rentals in Singapore in the corporate sector can make sense for some time until a business has discovered a agency footing. Finding Commercial Property Singapore takes a variety of time and effort but might be very rewarding in the long term.

is changing into a rising pattern among Singaporeans as the standard of living is increasing over time and more Singaporeans have abundance of capital to invest on properties. Investing in the personal properties in Singapore I would like to applaud you for arising with such a book which covers the secrets and techniques and tips of among the profitable Singapore property buyers. I believe many novice investors will profit quite a bit from studying and making use of some of the tips shared by the gurus." – Woo Chee Hoe Special bonus for consumers of Secrets of Singapore Property Gurus Actually, I can't consider one other resource on the market that teaches you all the points above about Singapore property at such a low value. Can you? Condominium For Sale (D09) – Yong An Park For Lease

In 12 months 2013, c ommercial retails, shoebox residences and mass market properties continued to be the celebrities of the property market. Models are snapped up in report time and at document breaking prices. Builders are having fun with overwhelming demand and patrons need more. We feel that these segments of the property market are booming is a repercussion of the property cooling measures no.6 and no. 7. With additional buyer's stamp responsibility imposed on residential properties, buyers change their focus to commercial and industrial properties. I imagine every property purchasers need their property funding to understand in value. The Dittus-Bölter correlation (1930) is a common and particularly simple correlation useful for many applications. This correlation is applicable when forced convection is the only mode of heat transfer; i.e., there is no boiling, condensation, significant radiation, etc. The accuracy of this correlation is anticipated to be ±15%.

For a fluid flowing in a straight circular pipe with a Reynolds number between 10 000 and 120 000 (in the turbulent pipe flow range), when the fluid's Prandtl number is between 0.7 and 120, for a location far from the pipe entrance (more than 10 pipe diameters; more than 50 diameters according to many authors) or other flow disturbances, and when the pipe surface is hydraulically smooth, the heat transfer coefficient between the bulk of the fluid and the pipe surface can be expressed explicitely as:

${hd \over k}={0.023}\,\left({jd \over \mu }\right)^{0.8}\,\left({\mu c_{p} \over k}\right)^{n}$

which can be simplified to give:

$h={0.023}{k^{1-n}j^{0.8}c_{p}^{n} \over \mu ^{0.8-n}d^{0.2}}$

where

$d$ hydraulic diameter

$k$ - thermal conductivity of the bulk fluid

$\mu$ viscosity

$j$ mass flux

$c_{p}$ isobaric heat capacity

n = 0.4 for heating (wall hotter than the bulk fluid) and 0.33 for cooling (wall cooler than the bulk fluid).

The fluid properties necessary for the application of this equation are evaluated at the bulk temperature thus avoiding iteration

Forced convection, External flow

In analyzing the heat transfer associated with the flow past the exterior surface of a solid, the situation is complicated by phenomena such as boundary layer separation. Various authors have correlated charts and graphs for different geometries and flow conditions. For Flow parallel to a Plane Surface, where x is the distance from the edge and L is the height of the boundary layer, a mean Nusselt number can be calculated using the Colburn analogy.

Thom correlation

There exist simple fluid-specific correlations for heat transfer coefficient in boiling. The Thom correlation is for flow boiling of water (subcooled or saturated at pressures up to about 20 MPa) under conditions where the nucleate boiling contribution predominates over forced convection. This correlation is useful for rough estimation of expected temperature difference given the heat flux:

$\Delta T_{sat}=22.5\cdot {q}^{0.5}\exp(-P/8.7)$

where:

$\Delta T_{sat}$ is the wall temperature elevation above the saturation temperature, K

q is the heat flux, MW/m²

P is the pressure of water, MPa

Note that this empirical correlation is specific to the units given.

Heat transfer coefficient of pipe wall

The resistance to the flow of heat by the material of pipe wall can be expressed as a "heat transfer coefficient of the pipe wall". However, one needs to select if the heat flux is based on the pipe inner or the outer diameter.

where k is the effective thermal conductivity of the wall material and x is the wall thickness.

If the above assumption does not hold, then the wall heat transfer coefficient can be calculated using the following expression:

$h_{wall}={2k \over {d_{i}\ln(d_{o}/d_{i})}}$

where d_i and d_o are the inner and outer diameters of the pipe, respectively.

The thermal conductivity of the tube material usually depends on temperature; the mean thermal conductivity is often used.

Combining heat transfer coefficients

For two or more heat transfer processes acting in parallel, heat transfer coefficients simply add:

$h=h_{1}+h_{2}+\cdots$

For two or more heat transfer processes connected in series, heat transfer coefficients add inversely:

${1 \over h}={1 \over h_{1}}+{1 \over h_{2}}+\dots$

For example, consider a pipe with a fluid flowing inside. The rate of heat transfer between the bulk of the fluid inside the pipe and the pipe external surface is:

$q=\left({1 \over {{1 \over h}+{t \over k}}}\right)\cdot A\cdot \Delta T$

where

q = heat transfer rate (W)

h = heat transfer coefficient (W/(m²·K))

t = wall thickness (m)

k = wall thermal conductivity (W/m·K)

A = area (m²)

$\Delta T$ = difference in temperature.

Overall heat transfer coefficient

The overall heat transfer coefficient $U$ is a measure of the overall ability of a series of conductive and convective barriers to transfer heat. It is commonly applied to the calculation of heat transfer in heat exchangers, but can be applied equally well to other problems.

For the case of a heat exchanger, $U$ can be used to determine the total heat transfer between the two streams in the heat exchanger by the following relationship:

$q=UA\Delta T_{LM}$

where

$q$ = heat transfer rate (W)

$U$ = overall heat transfer coefficient (W/(m²·K))

$A$ = heat transfer surface area (m²)

$\Delta T_{LM}$ = log mean temperature difference (K)

The overall heat transfer coefficient takes into account the individual heat transfer coefficients of each stream and the resistance of the pipe material. It can be calculated as the reciprocal of the sum of a series of thermal resistances (but more complex relationships exist, for example when heat transfer takes place by different routes in parallel):

${\frac {1}{UA}}=\sum {\frac {1}{hA}}+\sum R$

where

R = Resistance(s) to heat flow in pipe wall (K/W)

Other parameters are as above.

The heat transfer coefficient is the heat transferred per unit area per kelvin. Thus area is included in the equation as it represents the area over which the transfer of heat takes place. The areas for each flow will be different as they represent the contact area for each fluid side.

The thermal resistance due to the pipe wall is calculated by the following relationship:

$R={\frac {x}{k\cdot A}}$

where

x = the wall thickness (m)

k = the thermal conductivity of the material (W/(m·K))

A = the total area of the heat exchanger (m²)

This represents the heat transfer by conduction in the pipe.

The thermal conductivity is a characteristic of the particular material. Values of thermal conductivities for various materials are listed in the list of thermal conductivities.

As mentioned earlier in the article the convection heat transfer coefficient for each stream depends on the type of fluid, flow properties and temperature properties.

Some typical heat transfer coefficients include:

• Air - h = 10 to 100 W/(m²K)
• Water - h = 500 to 10,000 W/(m²K)

Thermal resistance due to fouling deposits

Surface coatings can build on heat transfer surfaces during heat exchanger operation due to fouling. These add extra thermal resistance to the wall and may noticeably decrease the overall heat transfer coefficient and thus performance. (Fouling can also cause other problems.)

The additional thermal resistance due to fouling can be found by comparing the overall heat transfer coefficient determined from laboratory readings with calculations based on theoretical correlations. They can also be evaluated from the development of the overall heat transfer coefficient with time (assuming the heat exchanger operates under otherwise identical conditions). This is commonly applied in practice, e.g. The following relationship is often used:

${\frac {1}{U_{exp}}}$ = ${\frac {1}{U_{pre}}}+R_{f}$

where

$U_{exp}$ = overall heat transfer coefficient based on experimental data for the heat exchanger in the "fouled" state, ${\frac {W}{m^{2}K}}$

$U_{pre}$ = overall heat transfer coefficient based on calculated or measured ("clean heat exchanger") data, ${\frac {W}{m^{2}K}}$

$R_{f}$ = thermal resistance due to fouling, ${\frac {m^{2}K}{W}}$

See also

• Convective heat transfer
• Heat sink
• Convection
• Churchill-Bernstein Equation
• Heat
• Heat pump
• Heisler Chart
• Thermal conductivity
• Thermal-hydraulics
• Fourier number
• Nusselt number

References

43 year old Petroleum Engineer Harry from Deep River, usually spends time with hobbies and interests like renting movies, property developers in singapore new condominium and vehicle racing. Constantly enjoys going to destinations like Camino Real de Tierra Adentro.

External links

• Overall Heat Transfer Coefficients
• Correlations for Convective Heat Transfer
• Heat Transfer fundamentals
• Heat Transfer Coefficient Calculator