|
|
| Line 1: |
Line 1: |
| [[Image:microstrip geometry.svg|thumb|right|200px|Cross-section of microstrip geometry. Conductor (A) is separated from ground plane (D) by dielectric substrate (C). Upper dielectric (B) is typically air.]] '''Microstrip''' is a type of electrical [[transmission line]] which can be fabricated using [[printed circuit board]] technology, and is used to convey [[microwave]]-frequency signals. It consists of a conducting strip separated from a [[ground plane]] by a [[dielectric]] layer known as the substrate. Microwave components such as [[microstrip antenna|antennas]], [[directional coupler|coupler]]s, [[distributed element filter|filter]]s, [[Power dividers and directional couplers#Other power dividers|power divider]]s etc. can be formed from microstrip, the entire device existing as the pattern of metallization on the substrate. Microstrip is thus much less expensive than traditional [[waveguide (electromagnetism)|waveguide]] technology, as well as being far lighter and more compact. Microstrip was developed by ITT laboratories as a competitor to [[stripline]] (first published by Grieg and Engelmann in the December 1952 IRE proceedings<ref>{{cite journal|last=Grieg|first=D. D.|coauthors=Engelmann, H. F.|date=Dec 1952|title=Microstrip-A New Transmission Technique for the Klilomegacycle Range|journal=Proceedings of the IRE|volume=40|issue=12|pages=1644–1650|issn=0096-8390|doi=10.1109/JRPROC.1952.274144}}</ref>).
| | == that the inventory list you have == |
|
| |
|
| The disadvantages of microstrip compared with waveguide are the generally lower power handling capacity, and higher losses. Also, unlike waveguide, microstrip is not enclosed, and is therefore susceptible to cross-talk and unintentional radiation.
| | Could not help but ask.<br><br>'We have a total over 1,[http://www.alleganycountyfair.org/_vti_cnf/rakuten_oakley_22.htm オークリー サングラス カタログ],120,000 Thunder Stone.' Feng Luo to see the flood,[http://www.alleganycountyfair.org/_vti_cnf/rakuten_oakley_33.htm オークリー 激安 サングラス], Thor, 'Brother,[http://www.alleganycountyfair.org/_vti_cnf/rakuten_oakley_16.htm オークリー サングラス 調光], brother,[http://www.alleganycountyfair.org/_vti_cnf/rakuten_oakley_48.htm オークリー サングラス 手入れ], that the inventory list you have,[http://www.alleganycountyfair.org/_vti_cnf/rakuten_oakley_0.htm オークリー サングラス 店舗], what are you going to change?'<br><br>'D6-class rail guns!' Raytheon some expectations, 'that's D6 level railgun,[http://www.alleganycountyfair.org/_vti_cnf/rakuten_oakley_2.htm ロードバイク サングラス オークリー], on behalf of the domain master six strong bands which are difficult to block the shot! Such restricted weapon ...... or D6 level is absolutely price. leave this land, no this shop. '<br><br>'ah,[http://www.alleganycountyfair.org/_vti_cnf/rakuten_oakley_42.htm オークリー サングラス レーダー].' Luo Feng nor by the nod.<br><br>D6-class rail guns!<br><br>hide, much to the domain master to a strong artillery, bombers kill directly. This restricted the main weapon ...... many circles are not. Not the money to buy, but not channels. Or on the main sector concerned,[http://www.alleganycountyfair.org/_vti_cnf/rakuten_oakley_28.htm オークリー サングラス オークション], is not worth buying.<br><br>'# 11 'stars of the heart'.' Hung eyes shine, 'which stars of the heart, and you know that.'<br><br>'ah.'<br><br>Luo Feng some heart. |
| | | 相关的主题文章： |
| For lowest cost, microstrip devices may be built on an ordinary [[FR-4]] (standard PCB) substrate. However it is often found that the dielectric losses in FR4 are too high at microwave frequencies, and that the [[dielectric constant]] is not sufficiently tightly controlled. For these reasons, an [[alumina]] substrate is commonly used.
| | <ul> |
| | | |
| On a smaller scale, microstrip transmission lines are also built into [[monolithic microwave integrated circuit]]s.
| | <li>[http://0752114.com/home.php?mod=space&uid=473071 http://0752114.com/home.php?mod=space&uid=473071]</li> |
| | | |
| Microstrip lines are also used in high-speed digital PCB designs, where signals need to be routed from one part of the assembly to another with minimal distortion, and avoiding high cross-talk and radiation.
| | <li>[http://www.arichat.com/cgi-bin/gbks/guestbook.cgi http://www.arichat.com/cgi-bin/gbks/guestbook.cgi]</li> |
| | | |
| Microstrip is very similar to [[stripline]] and [[coplanar waveguide]],{{Citation needed|date=July 2011}} and it is possible to integrate all three on the same substrate.
| | <li>[http://www.17ws8.com/bbs/home.php?mod=space&uid=255862 http://www.17ws8.com/bbs/home.php?mod=space&uid=255862]</li> |
| | | |
| == Inhomogeneity ==
| | </ul> |
| The electromagnetic wave carried by a microstrip line exists partly in the [[dielectric]] substrate, and partly in the air above it. In general, the [[dielectric constant]] of the substrate will be different (and greater) than that of the air, so that the wave is travelling in an inhomogeneous medium. In consequence, the propagation velocity is somewhere between the speed of radio waves in the substrate, and the speed of radio waves in air. This behaviour is commonly described by stating the effective dielectric constant (or effective relative permittivity) of the microstrip; this being the dielectric constant of an equivalent homogeneous medium (i.e., one resulting in the same propagation velocity).
| |
| | |
| Further consequences of an inhomogeneous medium include:
| |
| | |
| * The line will not support a true [[Transverse electric and magnetic mode|TEM]] wave; at non-zero frequencies, both the [[electric field|E]] and [[magnetic field|H fields]] will have longitudinal components (a [[Transverse electric and magnetic mode|hybrid mode]]).<ref name="denlinger1971">E. J. Denlinger, “A frequency dependent solution for microstrip transmission lines”; ''IEEE Trans. Microwave Theory Tech.'', vol. MTT-19, pp. 30-39, Jan. 1971.</ref> The longitudinal components are small however, and so the dominant mode is referred to as quasi-TEM.
| |
| * The line is [[dispersion (optics)|dispersive]]. With increasing frequency, the effective dielectric constant gradually climbs towards that of the substrate, so that the [[phase velocity]] gradually decreases.<ref name="denlinger1971"/><ref name="cory1981">H. Cory, “Dispersion characteristics of microstrip lines”; ''IEEE Trans. Microwave Theory Tech.'', vol. MTT-29, pp. 59-61, Jan. 1981.</ref> This is true even with a non-dispersive substrate material (the substrate dielectric constant will usually fall with increasing frequency).
| |
| * The [[characteristic impedance]] of the line changes slightly with frequency (again, even with a non-dispersive substrate material). The characteristic impedance of non-TEM modes is not uniquely defined, and depending on the precise definition used, the impedance of microstrip either rises, falls, or falls then rises with increasing frequency.<ref name="bianco1978">B. Bianco, L. Panini, M. Parodi, and S. Ridetlaj “Some considerations about the frequency dependence of the characteristic impedance of uniform microstrips”: ''IEEE Trans. Microwave Theory Tech.'', vol. MTT-26, pp. 182-185, March 1978.</ref> The low-frequency limit of the characteristic impedance is referred to as the quasi-static characteristic impedance, and is the same for all definitions of characteristic impedance.
| |
| * The [[wave impedance]] varies over the cross-section of the line.
| |
| | |
| == Characteristic impedance ==
| |
| A closed-form approximate expression for the quasi-static [[characteristic impedance]] of a microstrip line was developed by [[Harold Alden Wheeler|Wheeler]]:<ref>H. A. Wheeler, “Transmission-line properties of parallel wide strips by a conformal-mapping approximation”, ''IEEE Trans. Microwave Theory Tech.'', vol. MTT-12, pp. 280-289, May 1964.</ref><ref name="wheeler1965">H. A. Wheeler, “Transmission-line properties of parallel strips separated by a dielectric sheet”, ''IEEE Tran. Microwave Theory Tech.'', vol. MTT-13, pp. 172-185, Mar. 1965.</ref><ref name="wheeler1977">H. A. Wheeler, “Transmission-line properties of a strip on a dielectric sheet on a plane”, ''IEEE Tran. Microwave Theory Tech.'', vol. MTT-25, pp. 631-647, Aug. 1977.</ref>
| |
| | |
| :<math>Z_\textrm{microstrip} = \frac{Z_{0}}{2 \pi \sqrt{2 (1 + \varepsilon_{r})}} \mathrm{ln}\left( 1 + \frac{4 h}{w_\textrm{eff}} \left( \frac{14 + \frac{8}{\varepsilon_{r}}}{11} \frac{4 h}{w_\textrm{eff}} + \sqrt{\left( \frac{14 + \frac{8}{\varepsilon_{r}}}{11} \frac{4 h}{w_\textrm{eff}}\right)^{2} + \pi^{2} \frac{1 + \frac{1}{\varepsilon_{r}}}{2}}\right)\right),</math>
| |
| | |
| where <math>w_\mathrm{eff}</math> is the ''effective width'', which is the actual width of the strip, plus a correction to account for the non-zero thickness of the metallization:
| |
| | |
| :<math>w_\textrm{eff} = w + t \frac{1 + \frac{1}{\varepsilon_{r}}}{2 \pi} \mathrm{ln}\left( \frac{4 e}{\sqrt{\left( \frac{t}{h}\right)^{2} + \left( \frac{1}{\pi} \frac{1}{\frac{w}{t} + \frac{11}{10}}\right)^{2}}}\right).</math>
| |
| | |
| Here ''Z''<sub>0</sub> is the [[impedance of free space]], ''ε''<sub>r</sub> is the [[relative permittivity]] of substrate, ''w'' is the width of the strip, ''h'' is the thickness ("height") of substrate, and ''t'' is the thickness of the strip metallization.
| |
| | |
| This formula is asymptotic to an exact solution in three different cases
| |
| | |
| #<math>w \gg h</math>, any <math>\varepsilon_{r}</math> (parallel plate transmission line),
| |
| #<math>w \ll h</math>, <math>\varepsilon_{r} = 1</math> (wire above a ground-plane) and
| |
| #<math>w \ll h</math>, <math>\varepsilon_{r} \gg 1.</math>
| |
| | |
| It is claimed that for most other cases, the error in impedance is less than 1%, and is always less than 2%.<ref name="wheeler1977"/> By covering all aspect-ratios in one formula, Wheeler 1977 improves on Wheeler 1965<ref name="wheeler1965"/> which gives one formula for <math>w / h > 3.3</math> and another for <math>w / h \le 3.3</math> (thus introducing a discontinuity in the result at <math>w / h = 3.3</math>). Nevertheless, the 1965 paper is perhaps the more often cited. A number of other approximate formulae for the characteristic impedance have been advanced by other authors. However, most of these are applicable to only a limited range of aspect-ratios, or else cover the entire range piecewise.
| |
| | |
| Curiously, Harold Wheeler disliked both the terms 'microstrip' and 'characteristic impedance', and avoided using them in his papers.
| |
| | |
| ==Bends==
| |
| In order to build a complete circuit in microstrip, it is often necessary for the path of a strip to turn through a large angle. An abrupt 90° bend in a microstrip will cause a significant portion of the signal on the strip to be reflected back towards its source, with only part of the signal transmitted on around the bend. One means of effecting a low-reflection bend, is to curve the path of the strip in an arc of radius at least 3 times the strip-width.<ref>T.H. Lee, Planar Microwave Engineering; ''Cambridge University Press'', pp. 173-174, 2004.</ref> However, a far more common technique, and one which consumes a smaller area of substrate, is to use a mitred bend.
| |
| | |
| [[Image:microstrip-bend.svg|thumb|left|200px|Microstrip 90° mitred bend. The percentage mitre is 100x/d]] To a first approximation, an abrupt un-mitred bend behaves as a shunt capacitance placed between the ground plane and the bend in the strip. Mitring the bend reduces the area of metallization, and so removes the excess capacitance. The percentage mitre is the cut-away fraction of the diagonal between the inner and outer corners of the un-mitred bend. | |
| | |
| The optimum mitre for a wide range of microstrip geometries has been determined experimentally by Douville and James.<ref name="douville1978">R. J. P. Douville and D. S. James, Experimental study of symmetric microstrip bends and their compensation; ''IEEE Trans. Microwave Theory Tech.'', vol. MTT-26, pp. 175-182, Mar. 1978.</ref> They find that a good fit for the optimum percentage mitre is given by
| |
| | |
| :<math>M = 100 \frac{x}{d} \% = (52 + 65 e^{- \frac{27}{20} \frac{w}{h}}) \%</math>
| |
| | |
| subject to <math>w/h \ge 0.25</math> and the with the substrate dielectric constant <math>\varepsilon_{r} \le 25</math>. This formula is entirely independent of <math>\varepsilon_{r}</math>. The actual range of parameters for which Douville and James present evidence is <math>0.25 \le w/h \le 2.75</math> and <math>2.5 \le \varepsilon_{r} \le 25</math>. They report a [[VSWR]] of better than 1.1 (i.e., a return better than −26 dB) for any percentage mitre within 4% (of the original <math>d</math>) of that given by the formula. At the minimum <math>w/h</math> of 0.25, the percentage mitre is 98.4%, so that the strip is very nearly cut through.
| |
| | |
| For both the curved and mitred bends, the electrical length is somewhat shorter than the physical path-length of the strip.
| |
| | |
| == See also ==
| |
| * [[Distributed element filter]]
| |
| * [[Spurline]], a microstrip notch-filter
| |
| | |
| == References ==
| |
| {{Reflist}}
| |
| | |
| == External links ==
| |
| * [http://www.microwaves101.com/encyclopedia/microstrip.cfm Microstrip in Microwave Encyclopedia]
| |
| * [http://mcalc.sourceforge.net/ Microstrip Analysis/Synthesis Calculator]
| |
| | |
| [[Category:Microwave technology]]
| |
| [[Category:Electronics]]
| |
| [[Category:Signal cables]]
| |
that the inventory list you have
Could not help but ask.
'We have a total over 1,オークリー サングラス カタログ,120,000 Thunder Stone.' Feng Luo to see the flood,オークリー 激安 サングラス, Thor, 'Brother,オークリー サングラス 調光, brother,オークリー サングラス 手入れ, that the inventory list you have,オークリー サングラス 店舗, what are you going to change?'
'D6-class rail guns!' Raytheon some expectations, 'that's D6 level railgun,ロードバイク サングラス オークリー, on behalf of the domain master six strong bands which are difficult to block the shot! Such restricted weapon ...... or D6 level is absolutely price. leave this land, no this shop. '
'ah,オークリー サングラス レーダー.' Luo Feng nor by the nod.
D6-class rail guns!
hide, much to the domain master to a strong artillery, bombers kill directly. This restricted the main weapon ...... many circles are not. Not the money to buy, but not channels. Or on the main sector concerned,オークリー サングラス オークション, is not worth buying.
'# 11 'stars of the heart'.' Hung eyes shine, 'which stars of the heart, and you know that.'
'ah.'
Luo Feng some heart.
相关的主题文章：