|
|
| Line 1: |
Line 1: |
| A '''state variable filter''' is a type of [[active filter]]. It consists of one or more [[integrator]]s, connected in some feedback configuration. Any [[LTI system]] can be described as a [[State space (controls)|state-space model]], with n state variables for an nth-order system. A state variable filter realizes the state-space model directly. The instantaneous output voltage of one of the integrators corresponds to one of the state-space model's state variables.
| | Hi there, I am Sophia. He works as a bookkeeper. Her family members life in Ohio but her husband desires them to transfer. She is really fond of caving but she doesn't have the time lately.<br><br>Feel free to visit my web site: free psychic reading [[http://ustanford.com/index.php?do=/profile-38218/info/ this ustanford.com]] |
| | |
| == Kerwin-Huelsman-Newcomb (KHN) Biquad Filter Example ==
| |
| | |
| The example given below can produce simultaneous [[lowpass]], [[highpass]] and [[bandpass]] outputs from a single input. This is a second-order ([[biquad filter|biquad]]) filter. Its derivation comes from rearranging a high-pass filter's transfer function, which is the ratio of two quadratic functions. The rearrangement reveals that one signal is the sum of integrated copies of another. That is, the rearrangement reveals a state variable filter structure. By using different states as outputs, different kinds of filters can be produced. In more general state variable filter examples, additional filter order is possible with more integrators (i.e., more states).
| |
| | |
| [[Image:State-variable-filter.png]]
| |
| | |
| The signal input is marked Vin; the LP, HP and BP outputs give the lowpass, highpass and bandpass filtered signals respectively.
| |
| | |
| For simplicity, we set:
| |
| | |
| <math>R_{f1} = R_{f2}</math>
| |
| | |
| <math>C_1 = C_2</math> | |
| | |
| <math>R_1=R_2</math>
| |
| | |
| Then:
| |
| | |
| <math>F_0 = \frac{1}{2\pi R_{f1}C_1}</math>
| |
| | |
| <math>Q = \left(1 + \frac{R_4}{R_q}\right)\left(\frac{1}{2+\frac{R_1}{R_g}}\right)</math>
| |
| | |
| The pass-band gain for the LP and HP outputs is given by:
| |
| | |
| <math>A_{HP} = A_{LP} = \frac{R_1}{R_G}</math>
| |
| | |
| It can be seen that the frequency of operation and the [[Q factor]] can be varied independently. This and the ability to switch between different filter responses make the state-variable filter widely used in analogue [[synthesizers]].
| |
| | |
| Values for a resonance frequency of 1 kHz are Rf1=Rf2=10k, C1=C2=15nF and R1=R2=10k
| |
| | |
| ==See also==
| |
| * [[Linear filter]]
| |
| * [[Biquad filter]]
| |
| | |
| ==References==
| |
| * Texas Instruments' [http://focus.ti.com/lit/ds/symlink/uaf42.pdf UAF42 Universal Active Filter] datasheet
| |
| | |
| * Analog Devices [http://www.analog.com/en/design-tools/dt-adisim-design-sim-tool/design-center/dt-adisim-design-sim-tool/Filter_Wizard/resources/fca.html Interactive Design Tools]
| |
| | |
| [[Category:Linear filters]]
| |
Hi there, I am Sophia. He works as a bookkeeper. Her family members life in Ohio but her husband desires them to transfer. She is really fond of caving but she doesn't have the time lately.
Feel free to visit my web site: free psychic reading [this ustanford.com]